style1 style2 style3

ASA tile adhesives


ASA Epoxy Prime 2 Part – high performance two part epoxy primer-Technical Data Sheet

By  Last updated: 4th September 2010

DESCRIPTION
Epoxy Prime 2 Part is a high performance two part epoxy primer specifically
developed for use on non-porous substrates such as dense, smooth concrete,
existing tiles and ASA approved polyurethane membranes. Epoxy Prime 2 Part
provides a good bond coat prior to the application of ASA approved tile adhesives,
ASA self levelling compounds and ASA approved waterproofing membranes.
FEATURES AND BENEFITS
• High bond strength
• Quick drying time
• Solvent free
• Adheres well to ASA approved
polyurethane membranes

RECOMMENDED FOR
ASA approved
polyurethane membranes
Dense, smooth concrete
Existing tiles
Metal surfaces
SURFACE PREPARATION
Surfaces must be clean, dry, and free from dust, wax, oil, laitance, curing compounds and all other contaminants likely
to prevent the Epoxy Prime 2 Part from bonding. Concrete should be allowed to cure for at least 28 days and cement
render for 7 days prior to application of Epoxy Prime 2 Part. ASA approved polyurethane membranes must have been
applied as per packaging directions and allowed to cure before the application of Epoxy Prime 2 Part.
MIXING
Stir both Part A and Part B of Epoxy Prime 2 Part with separate stirrers. Measure equal volumes (ratio 1:1) of Part A
and Part B and place into a clean container. Using a paint mixer and slow speed drill, mix thoroughly until a homogenous
mixture is achieved. Poor mixing will affect product performance. Do not mix more than what can be used in 1 hour at
25˚C.
APPLICATION
Apply Epoxy Prime 2 Part onto the correctly prepared surface using a brush or roller, ensuring full coverage of the
substrate. When using over ASA approved polyurethane membranes it is imperative that the membrane is cleaned
using a sugar soap solution. The membrane must then be thoroughly rinsed with clean water and allowed to dry. If full
coverage is not achieved with one coat then a second coat must be applied in a perpendicular direction to the first coat
(re-coat time is 4 hours). Epoxy Prime 2 Part must be covered within 4 days of final coat. If the Epoxy Prime 2 Part is
showing signs of contamination such as dust, paint or any other material that will compromise adhesion, then the area
must be washed thoroughly with a sugar soap solution, rinsed and allowed to dry.
TILING
Commence tiling after Epoxy Prime 2 Part has cured. It is recommended that tiling be carried out within 4 days of
Epoxy Prime 2 Part application as this eliminates the possibility of surface contamination. If tiling is carried out after
this time, ensure surface is clean and dry.
RECOMMENDED ADHESIVES
ASA Fixall mixed with undiluted ASA Megalastic, ASA Conflex and ASA Asaflex.
CLEAN UP
Tools and equipment can be cleaned with warm water and detergent prior to the Epoxy Prime 2 Part drying.
PACKAGING
20 litre, 8 litre and 4 litre kits.
POT LIFE
1 hour at 25˚C. A higher temperature will reduce pot life.
COVERAGE
1litre of Epoxy Prime 2 Part will cover approximately 8m² per coat depending on substrate porosity.
SAFETY PRECAUTIONS
Avoid contact with skin and eyes. Use eyewear, barrier cream and protective gloves. Use only soap and water for
cleaning hands and skin. Ensure adequate ventilation and avoid breathing vapours. Keep away from children. If
swallowed do not induce vomiting. Give plenty of milk or water. Seek medical advice. For more detailed information
refer to product MSDS.

Technical Data Sheet 

http://asanzltd.com/pdffiles/additives/EPOXYPRIME.pdf

FREEPHONE: 0508 222 777
FREEFAX: 0508 222500

148 Pavilion Drive
Air Park II
Auckland Airport
Auckland 2022
(off Montgomerie Road)

PO Box 112-119
Penrose, Auckland

telephone: 09 257 3580
facsimile: 09 257 3589
email: \n \n \n sales@asanzltd.com

Related articles





TileShop DOMAINNAMERZ CanadaTiles TileAustralia Tiler1 TilerAustralia 0800TILESCOM 0800tilesNZ Tiling TilesAmerica TilesNewYork 0800tilesUK LATiles Tiler
Ducati848 DDUCATI YAMAHAR6 TILESTORE HondaCBR BathroomDesign OpeninghoursWS TilesChicago WDPage NZVisitMe 027Directory SeeInsideWs
700JetSki 900 bikes Boats LovechToday Melbournetileshops ClosingNet Lovech V12 Fishoogle YourLove 359BG Rabotno 52 News AustraliaCarpet Ottyk
KawasakiNinja 0800tiler Ducati1198 Interiors ShopsSydney TileStore 1198 ChicagoTS TilesNZ StoreHours OpeningHours Adhesives Jet-Ski
TShops Grout CCCodes TSydney OPENINGHOURZ TSAustralia ClosimgZ OpeningEU tileshopsbiz closingUK iClosing NYTShops Tadhesives
LondonTS TorontoTS Brisbane ChicagoTS LSstores iOpening TilerNZ HOUSTONTS SydneyS LondonUK TadhesiveNZ AtilerNZ BBathrooms
NEWZEALANDVISIT HoursNZ iopeningUK JetSki LovechD UKTS TLDN4 TstoresINFO EuroexINFO TILESHOPZ SEEINSIDER TadhesivesUK